ŻƱ

Welcome to DaJing Lubrication Co., Ltd
Set ŻƱ | Add to Favorites | Back to ŻƱ
Products
Electric lubrication pump
Hand (foot) dynamic lubrication pump
Manual (electric) gasoline pump
Distributor, oiler
Dry oil control, control valve and other accessories
Thin oil lubrication device and thin oil station
Thin oil lubricated parts
Oil and gas lubrication systems and devices
Electrical control box
Piping accessories
contact details

Phone: 0513-83660308
0513-83905568
Fax: 0513-83660318
Mobile: 13767709919
Website: winvtech.com

Email: djrh888@163.com

You are here: ŻƱ> Products
24EJF-P two-position four-way directional valve (40MPa)

I. Overview
24EJF-P (formerly SA-V) two-position four-way reversing valve is an integrated reversing control device that uses a DC motor to drive the spool to open and close the fuel supply pipe or change the fuel supply direction ; Even under severe working conditions (such as low temperature or high viscosity grease), the action is still quite reliable.
The valve is suitable for dry and thin oil centralized lubrication systems with a nominal pressure below 40 MPa and the main branch pipelines of hydraulic systems. It can also be used as two-position four-way, two-position three-way and two-position two-way.

Technical parameters

model
Nominal pressure Mpa
Commutation time S
DC motor power W
Power supply voltage V
DC motor torque Nm
Weight kg
24EJF-P
40
0.5
10
-220
20
13

The medium used is a grease (NLGI0 # ~ 3 #) with a cone penetration of not less than 220 (25 C, 150g) or 1 / 10mm or a viscosity grade greater than N68. The working environment temperature is -20 C to 80 C.

3. Dimensions
Fourth, the working principle
The valve is mainly composed of a DC motor, a limit switch, a reversing valve body, a rectifier transformer device and other components installed on the same base plate and placed in a protective cover.
The electric control box in the system sends a commutation signal (issued by the differential pressure switch at the end of the system) to make the DC motor rotate, and the eccentric wheel drives the valve core to make a linear reciprocating motion. When the valve core reaches the required reversing position from the original position, the baffle at the end of the valve core triggers the limit switch to send an electric signal to the electric control box, instructs the DC motor to stop rotating, and completes the reversing process.
Five, instructions for use
1. The valve should be installed at the front end of the main and branch pipes of the system, and it should be located in a place that is easy to check and ventilated and dry, and there is no interference from the movement mechanism.
2. When used as a two-position two-way, the oil outlet “B” and the oil return “R” must be blocked.
3. When used as a two-position tee, the oil outlet "B" must be blocked.
4. The electric control wiring is connected according to the principle shown above.

Six, common faults and troubleshooting methods
1. The reversing valve is not reversing.
There may not be a commutation signal input to the motor, and the wire pins are welded off; the motor shaft and the eccentric are loose and not fastened; the foreign matter in the valve cavity enters the sliding core and is stuck, and other reasons can be ruled out and eliminated.
2. There is oil leakage at the two ends of the sliding core.
It is mainly caused by the damage of the two-end seals. It may be that the seals have been in stock for a long time or have been used for a long time. Replace the seals.
Copyright Qidong Dajing Lubrication Equipment Co., Ltd. Copyright ? 2009 winvtech.com All Rights Reserved
Address: Chengdong Industrial Park, Qidong City Phone: 0513-83660308, 83905568 Fax: 0513-83660318 Email: djrh888@163.com